CH PRECISION
M1 AMP

2-channel amplifier (with 1x ANALOG_BUF)
Actuellement indisponible
Prix catalogue
CHF 45'100.00

Description

Summum de musicalité et de technologie, l'Amplificateur de Puissance CH Precision M1 est un instrument de musique d'exception. Il est configurable et adaptable à l'infini. En mode MONO bridged il est capable de fournir 700 Watts en continu sous 8 Ohms! Tous les fabuleux instruments de musique CH Precision sont développés et fabriqués en +Suisse+.

Being able to truthfully and accurately reproduce today’s highest quality recordings has never been more challenging. Only when each element of the reproduction chain is able to precisely recreate the music’s time and level information can a genuine emotion be felt. The M1, CH Precision 1 Series’ most powerful amplifier was developed with this in mind. The leading-edge technological advancements implemented on the A1 were further refined, among others is the ExactBias circuitry and a finer loudspeaker matching.

Specified at 200W RMS into 8Ω in monaural mode, 2x 200W RMS into 8Ω in bi-amplification / Stereo modes and 700W RMS into 8Ω in bridge mode, the M1 houses a dedicated 2200VA power transformer providing the amplifier output stage with ample energy to accurately and effortlessly drive the most demanding loudspeakers.

Spécifications

Analog inputs:
  • Inputs type Balanced (XLR), one connector per board
  • Single-Ended (RCA & BNC), one connector per board
  • Input impedance Balanced: 94kΩ
  • Single-Ended: 47kΩ or 300Ω
  • Input stage JFET input stage
  • Ultra-low noise, discrete fully differential stage
  • 24dB range adjustable gain in 0.5dB steps
Amplification:
  • Amplification stage Ultra-low noise full discrete class AB design
  • 6 pairs of complementary output transistors
  • Bias Patent-pending bias circuitry for constant bias operation
  • Feedback User-adjustable local vs. global feedback ratio, from 0% to 100% in 10% steps 
  • Bandwidth DC to 450kHz (-3dB) at 1W into an 8Ω resistive load
  • Signal to Noise Ratio Better than 115dB in stereo and bi-amp modes
  • Better than 118dB in bridge mode
  • Total Harmonic Distortion + Noise Less than 0.1% with 0% global feedback
  • Less than 0.01% with 100% global feedback
Analog outputs:
  • Binding posts Two pairs of Argento binding posts for loudspeakers connection
  • Monitoring Non-intrusive DSP-based protection of the amplifier and connected loudspeakers
  • Instantaneous voltage & current values are permanently monitored on each channel
  • Protections Short-circuit protected
  • Disconnected loudspeaker detected
  • Over-temperature of the heatsink
  • Over-temperature of the output transistors
Power supply:
  • Transformer 2'200VA toroidal transformer for output stages, oversized for low-noise operation
  • 100VA separate toroidal transformer for input stages
  • Power capacitors  2x 100'000uF/100V 4-poles capacitors
  • Regulators Non-regulated symetrical power supply for the power stages
  • Eight local regulation stages for input/driver stages
  • Seven local regulation stages for the logic/display
General:
  • Display 480x272 pixels, 24bits color, AMOLED
  • Mains operation Selectable 100V, 115, 230V AC, 47-63Hz
  • Power supply consumption <1W (standby), 2200W max in operation
  • Dimensions/Weight 440 x 440 x 266mm (W x D x H), 75kg
  • Remote control Ethernet interface, TCP/IP control
Appelez
nos conseillers
de 8H à 17H
021 925 30 00
Appelez
nos conseillers
de 8H à 17H
021 925 30 00